uses of c45 steel

C45 steel Applications,C45 steel Physical properties

C45 steel Applications,C45 steel Physical properties steel ...

C45 steel is a medium carbon steel is used when greater strength and hardness is desired than in the "as rolled" condition. Extreme size accuracy, straightness and concentricity combine to minimize wear in high speed applications.

Contact Supplier

1045 / S45C / C45 Steel • Properties • Heat Treatment ...

C45 Steel Application 1045 steel is widely used for the industry application that required higher strength and wear resistance than low-carbon steel. And the typical applications are gears, shafts, rolls, crankshafts, sockets, bolts and etc.

Contact Supplier

C45 Medium Carbon Steel grade - Material Grades

Jul 19, 2018 · What is C45 Material? C45 grade steel is defined as a medium carbon steel offering tensile strengths in the modest range. The material can be maneuvered with hardening by means of quenching and tempering on focused and restricted areas. C45 can also be instigated with induction hardening up to the hardness level of HRC 55.

Contact Supplier

C45 / 1.0503 - SteelNumber - Chemical composition ...

C45 ( 1.0503 ) Cr + Mo + Ni = max 0.63 Weldability Due to the medium-high carbon content it can be welded with some precautions. Hardenability It has a low hardenability in water or oil; fit for surface hardening that gives this steel grade a high hardness of the hardened shell.

Contact Supplier

EN 1.0503 Material C45 Steel Equivalent, Properties ...

EN 10083-2 C45 steel (EN 1.0503) is a high strength medium carbon quality steel. Due to poor hardenability, C45 material is generally used in a normalized condition, and when the mechanical properties are required to be high, the quenching and tempering treatment is adopted.

Contact Supplier

C45 chemical composition - Sidastico EN

WARNING Although we have taken the utmost care in the drafting of the website, Sidastico Spa assumes no responsibility for the accuracy and exactness of the information set forth herein and reserves the right to change any part of the same without advance notice.

Contact Supplier

C45 steel

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. C45 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Contact Supplier

C45 Round Bar AISI 1045 DIN 1.1191 - Otai Special Steel

Application of DIN Carbon Steel C45 Round Bar. Quenched and subsequently tempered steel for C45 steel grade round bar, steel plate, flat and square is used for axles, bolts, forged connecting rods, crankshafts, torsion bars, light gears, guide rods, screws, forgings, wheel tyres, shafts, sickles, axes, knives, wood working drills, hammers, etc.

Contact Supplier

C45 steel sheet,C45 steel Mechanical Properties,C45 steel ...

C45 is a medium carbon steel is used when greater strength and hardness is desired than in the "as rolled" condition. Extreme size accuracy, straightness and concentricity combine to minimize wear in high speed applications. Turned, ground and polished.

Contact Supplier

C45

Variant SB8673 / SB-C45 is a variant with a narrowed chemical composition in order to reach a high hardenability and it is fine grain treated with Al. Variant SB1672 is a standard variant of C45 with medium Carbon for all purpose use. Variant SB1671 is a C45 with slightly lower alloy content and with an increased Sulphur content

Contact Supplier

C45 steel sheet,C45 steel Mechanical Properties,C45 steel ...

C45 is a medium carbon steel is used when greater strength and hardness is desired than in the "as rolled" condition. Extreme size accuracy, straightness and concentricity combine to minimize wear in high speed applications. Turned, ground and polished. Soft Annealing Heat to 680-710oC, cool slowly in …

Contact Supplier

C45 Carbon Steel - West Yorkshire Steel

C45 is widely used for components that require better properties than mild steel but does not justify the costs of an alloy steel. Available from stock in bar, C45 can be cut to your requirements. We also offer flame cut plates cut to your required sizes and normalised. C45 flame cut plates can be supplied surface ground or precision ground.

Contact Supplier

C45 Steel - DIN 17200 - EN 10083 Standard quenched and ...

DIN C45 steel flat bar is widely used for all industrial applications requiring more wear resistance and strength. Typical applications as Gears Pins Rams Shafts Rolls Sockets Axles Spindles Worms Bolts Ratchets Light gears Studs Crankshafts Guide rods Connecting rods Torsion bars, Hydraulic clamps

Contact Supplier

What are equivalent grades of c45 steel and en19 steel ...

Nov 12, 2010 · What is the difference between C45 steel and EN31 steel? C45 is basically a 0.45% medium carbon steel and en31 has between 0.95 and 1.1 …

Contact Supplier

C45 Carbon Steel Plates, C45 Sheets, C45 Plates ...

High Carbon Steel C45 S45C 1045 C-45 Sheets, C45 Boiler Plates, C45 Shim Sheets, C45 Carbon Steel Circle, C45 Cold Rolled Plates, C45 Coils, C45 Carbon Steel Plates Dealer in India. Ganpat Industrial Corporation is a recognized trader, dealer and stockist of C45 CS Sheets Plates, which is also used in domestic, professional or industrial areas.

Contact Supplier

S45C (JIS ) - Worldwide equivalent grades - Steel Number

C45E (1.1191) , C45 (1.0503) , S45C (Japan, JIS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the …

Contact Supplier

China 45 Steel Equivalent, Mechanical Properties ...

#45 material is widely used in mechanical manufacturing and high-strength moving parts, such as turbine impellers, compressor pistons, shafts, gears, racks, steel wire and wire ropes.

Contact Supplier

15 Common Applications for Versatile 4140 Steel - Otai ...

AISI 4140 steel grade is a versatile steel grade. 4140 material is widely used in a lots of industrial fields. It is a chromium-molybdenum alloy steel. It is a chromium-molybdenum alloy steel. The chromium content provides good hardness penetration, and the molybdenum content ensures uniform hardness and …

Contact Supplier

AISI 1045 Medium Carbon Steel - AZoM

AISI 1045 steel is a medium tensile steel supplied in a black hot-rolled or normalized condition. It has a tensile strength of 570 - 700 MPa and Brinell hardness ranging between 170 and 210. AISI 1045 steel is characterized by good weldability, good machinability, and high strength and impact properties in either the normalized or hot-rolled condition.

Contact Supplier

What is the dead mild steel? - Quora

May 06, 2016 · It is used for making steel wires, sheets, rivets, screws, pipe, nail and chain. It has a tensile strength of 390 N/mm2 and a hardness of about 115 BHN. there are many company which produce their products from this raw material like tube, pipe, S31803 Duplex tube fitting , pipe fitting etc

Contact Supplier

Datasheet for Steel Grades Carbon Steel C45

This page is mainly introduced the C45 Datasheet, including chemical information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of C45,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application.

Contact Supplier

45 / 45 High quality structural carbon steel

45 ( 45 ) - High quality structural carbon steel chemical composition, mechanical and physical properties, hardness Database of steels and alloys (Marochnik) contains information about chemical composition and properties more then 3000 steels and alloys

Contact Supplier

C45 Carbon Steel - West Yorkshire Steel

in grade C45, which can be surface ground if required. Ground C45 steel bar can be supplied, providing a precision ground steel bar to tight tolerances. Contact our experienced sales team who will assist you with your C45 medium carbon steel enquiry. Plate Flat Diameter Applications C45 is widely used for many general engineering applications.

Contact Supplier

Leave a Comment